The washer has run 30 wash cycles and is indicating a reminder to run the Clean Washer with affresh cycle. Run the Clean Washer with affresh cycle. If the Clean Washer with afresh cycle is not turned on, the LED will stop flashing at the end of a wash cycle after running 3 more regular wash cycles. After 30 more wash cycles are completed, the Clean Washer LED will again flash at the end of a wash cycle as a reminder.
Check the following: Are both hot and cold water faucets completely turned on? Is the drain hose more than 96" 2. When excessive suds are detected, a suds routine automatically starts. This routine removes extra suds and assures proper rinsing of your garments. Use only HE High Efficiency detergents. Check the following: Is the washer door firmly shut?
The door must be completely closed for the washer to operate. The door may look closed, but may not be latched. Open the door and close firmly. Were you washing a large load? Before you close the washer door, check for laundry items sticking out beyond the door opening. Leave enough space in the washer to allow the clothes to tumble freely. An tightly packed basket may keep the door from shutting completely. Reduce your load size if needed. If an overload is detected, the washer will drain any water and detergent in the washer.
Remove several items and add HE detergent. Allow the washer to continue. Washer taking too long to fill. Drain extends more than 4. Use drain hose form and attach securely to drainpipe or tub. Do not tape over drain opening. Washer taking too long to drain water.
This code will appear at the end of the wash cycle to indicate that cold water hose is connected to the hot water inlet and hot water hose is connected to the cold water inlet. Close the lid to clear the display. If the lid is left open for more than 10 minutes, the cycle will reset and water in the washer will drain.
Appliance has no or insufficient water supply. If the fault occurs again, contact our After-Sales Service. Waste water is not pumped out. If the fault occurs again, contact our After-Sales-Service. Tilt the appliance forward carefully to allow collected water to flow out from the bottom. If any of the faults described above persist, unplug the appliance, turn off the water tap and contact our After-Sales Service.
Appliance stops during the programme. Open lid and close drum flaps, then select and start desired programme again. If fault persists, notify our After-Sales Service. Tilt appliance forward carefully to allow collected water to flow out from the bottom. If faults persist, unplug the appliance, turn off the water tap and contact our After-Sales Service. May appear for very water-soaking laundry, or if you added too much laundry for a programme destined for small loads only. Do not overload the washing machine.
Tilt the appliance forward carefully a second person must help you to allow collected water to flow out from the bottom. Water level is not reached within a defined time in normal wash cycle. Dislodge any debris build up in the hose inside the outer tub. Verify there is not a siphon problem. Check all hoses for possible leaks. Plug in washer or reconnect power 6. Verify pressure switch operation.
If the drain time exceeds 4 minutes the water valves turn off. Check the drain hose and make sure it is not plugged or kinked. Remove hose from pressure switch. Check the electrical connections at the pump and make sure the pump is running. Check the drain pump filter for foreign objects.
If the above does not correct the problem, go to step 8. Replace the pump. If there is water in the unit: - Verify drain pump operation. Dislodge any debris build up in the hose inside the outer tub 1. Overflow level has been reached, and last for more than 2 seconds. In an overflow condition, the door remains locked and the drain pump runs constantly, and after 10 minutes, door will be unlocked in order to cut off the valves power.
Then if overflow s till happens, start pump again. Turn off hot and cold water faucets and unplug the unit before servicing. Unplug washer or disconnect power, if water still flows into the washer, replace the water valve. Check for drain pump failure. Check the inlet valve for proper shut off. Check the pressure switch for proper operation. Rerrove hose from pressure switch. Debris in side the hose will not allow the switch to sense a pressure change.
Only in factory test. Turn washer ON to verify pump operates. Check the water temperature sensor and connection to it 3. Be the first to review this product. Offers Available. Credit Card Debit Card. Extended Warranty None. Add Extended Warranty Details. Capacity: 7kg. Star Rating: 5 Star.
Excellent Choice! Notify me. Add to Cart Buy Now. Add to Wishlist. Sign In. Forgot Your Password? Get OTP. Create New Account? Create New Account. First Name. Chapter 9: Frigidaire Washing Machine Repair. Follow us on social media Facebook Twitter. All Rights Reserved. We seem to have lost our map and can't update your zip code right now. Please try again in a bit. This site only ships to the United States. Your location:. Order Status. Find a Store. Contact Us. Yes, I'd like to receive occasional special offers, promotions, or other e-mail marketing communications from Whirlpool and its affiliated brands.
For more information about our privacy practices and a list of affiliated brands, please read out Privacy Notice.
0コメント