Do not immerse the tool, battery pack, or charger in water or other liquid. If they are warm, allow them to cool down. Recharge only at room temperature. Do not set the charger on a soft surface. Keep the ventilation slots of the charger clear.
Keep at normal room temperature. If the outer seal is broken and the leakage gets on your skin: — Use soap and water to wash immediately. Never use the cord to carry the tool. Never pull on the cord to remove the plug from the power outlet. Keep cords away from heat, oil, sharp edges, or moving parts. Replace damaged cords immediately. They may create a fire. Do not use. Grounding Fig. A In the event of a malfunction or breakdown, grounding provides the path of least resistance for electric current, and reduces the risk of electric shock.
This battery charger is double insulated and has a two-pronged polarized plug one blade is wider than the other. This plug will fit into a polarized outlet only one way. If the plug does not fit fully in the outlet, reverse the plug. If it still does not fit, contact a qualified electrician to install the proper outlet. DO NOT change the plug in any way. IN ALL cases, make sure the outlet is properly grounded.
If you are not sure, have a certified electrician check the power outlet. A Fig. B Do not use an extension cord for the charger unless absolutely necessary. If you use an extension cord make sure the cord is in good condition. Use one heavy enough to carry the current your charger will draw. An undersized extension cord will cause a drop in line voltage, resulting in loss of power and overheating. The table below shows the correct size of extension cord to use, depending on cord length and the charger's ampere rating listed on the nameplate.
If in doubt, use the next heavier gauge. The smaller the gauge number is, the heavier the cord. Make sure your extension cord is properly wired and in good condition. Always replace a damaged cord or have it repaired by a qualified electrician. Protect your extension cord from sharp objects, excessive heat and damp or wet areas.
Use a separate electric circuit for your tools. Never use any other voltage or power source than common household V electrical power. The circuit must not beless than a 12 wire, and should be protected with a 15 A time-delayed fuse. Before connecting the charger to the power line, make sure the electric current is rated the same as the current stamped on the charger nameplate.
To reduce the risk of disconnection of charger cordfrom the extension cord during operation, make a knot Fig. Please check the contents of the carton with Fig.
Examine all the parts before using the cordless grass trimmer and battery charger. If any parts are missing or damaged, please call 1 for assistance. Basic safety precautions should always be followed.
The safety rules must be followed to avoid injury when using the grass trimmer. Allow the battery to fully discharge before recharging. It is recommended to charge the battery pack every 3 months when not in use. Plug the charger into an AC power outlet. Insert the battery pack 3 into the charge, the power LED 1 will turn red. Make sure the latch and battery are fully inserted into the charger. Wait 5 seconds, the status LED 2 will turn red, indicating a connection to the power source and that the battery is charging.
When the battery has become fully charged, the status LED 2 will turn green. The battery can be stored in the charger, as long as the charger is not plugged in. The battery is not shipped fully charged. It is recommended that the battery be fully charged before the initial use. It is recommended that the battery be charged every 3 months when the trimmer is not in use.
The battery's run time will improve after the third or fourth charge. To Remove the battery 1. Press in and hold the latch buttons 1 on both sides of the battery pack. Grasp the trigger handle 2 firmly. Pull the battery pack out of the handle.
NOTE: The battery pack fits snugly into the handle to prevent accidental dislodging. It may require a strong pull to remove. To Install 1. Align the tongue 3 of the battery pack with the cavity in the handle housing. Push the battery pack into the handle until both sides lock. The latch buttons will click when they lock. Do not use force when inserting the battery pack. It should slide into place and click. D To avoid injury, always remove the battery pack before installing the guard, changing a cutting line, or making any adjustments.
If the guard is damaged, do not use the grass trimmer until it is replaced. NOTE: Install the protective guard before operating the grass trimmer. Save www. Top www. Gift www. Sale www. Offer www. Deal www. Best www. Code www. Free www. Top fixitclub. These are sites, places offering fitness service meeting your search.
Additionally, by visiting our site regularly, users can get an asset of quality fitness destination for fitness centres, fitness equipment, fitness outfit, and much more. It is certain that you would get detailed information, even more service.
All our suggestion's results belong to your keywords which you type into the search box. We always prioritize all prestigious sources and make sure to meet your expectations. Golfaq is a useful destination for golf enthusiasts.
Come to Golfaq, a number of sites for high-quality golf services and products like golf equipment, golf courses are offered, which you can not find anywhere else. Yardworks Grass Trimmer and Edger - Unboxing www.
Coldstart of weedeater and yardworks lawn mowers www. Husqvarna String Trimmer Guard Replacement www. Black and Decker Trimmer Repair - Replacing the Dual Feed Line Replacement 7 11 16 www.
How to Replace the Guard Assembly on a Black and The battery is not shipped fully charged. It is recommended that the battery be fully charged before the initial use. It is recommended that the battery be charged every 3 months when the trimmer is not in use. To avoid injury, always remove the battery pack before installing the guard, changing a cutting line, or making any adjustments. If the guard is damaged, do not use the grass trimmer until it is replaced. NOTE: Install the protective guard before operating the grass trimmer.
It cannot be removed or disassembled. Insert the lower shaft 3 into upper shaft 2. Then turn the upper shaft 2 until lock button clicks into place. Turn the lower shaft 3 collar until locked into place. E1 Auxiliary handle Fig. F A spool of monofilament cutting line is preinstalled on the grass trimmer. When the cutting line needs replacing, insert a new spool. To remove the spool: 1. Disconnect trimmer from the power supply.
Avoid unintentional starting. Pull up edging coupler and turn handle end counterclockwise. Unscrew telescoping boom coupler and slide to desired position. Tighten telescoping boom coupler.
J While the grass trimmer is operating, the cutting line gets worn down and becomes shorter. This trimmer is equipped with Automatic Line Advancement, which automatically feeds additional line to the correct length as it wears down.
If the line does not automatically advance, the trimmer line may be tangled or empty.
0コメント